![]() ![]() ![]() Read Chris' guide to Rare Earth Magnets here. Then glue another magnet into recess located on the top of the hull and you have a safe and secure way of attaching the turret to the hull. To do this, simply glue a rare-earth magnet into the recess in the bottom of the turret rather than using the turret peg. The alternate method of attaching the turret to the hull is to use rare-earth magnets. Finally, attach the 105mm gun barrel to the gun mantlet.īelow: With the addition of the 105mm equipped turret the M4 Sherman (105mm) in now fully assembled. Next, attach the 105mm gun mantlet.īelow: The back of the 105mm gun mantlet also has an arrow to indicate which way is up.īelow: The 105mm gun mantlet attached to the front of the turret. Attach the 105mm gun trunnion to the front of the turret.īelow: The back of the 105mm gun trunnion has an arrow to indicate which way is up.īelow: The 105mm trunnion attached to the front of the turret. Attach the hull MG to the glacis plate.īelow: With the hull MG in place, the hull of the M4 Sherman (105mm) is fully assembled. Begin by attaching the glacis plate to the front of the hull. Next, attach the upper hull section to the lower hull.īelow: With the stowage rack attached, the basic hull is now fully assembled. Finally, attach the 76mm gun to the gun mantlet.īelow: The M4 Sherman (Late 76mm) fully assembled. The back of the 76mm gun mantlet has an arrow to indicate which way is up. Next, attach the gun mantlet to the front of the turret. 50 cal AA MG to the pintle mount located on the top of the turret.īelow: The. Next, add the hatch to the commander's cupola. Begin by joining the upper and lower sections of the turret. Attach the hull MG to the glacis plate.īelow: With the hull MG in place, the hull of the M4 Sherman (Late 76mm) is fully assembled. Attach the stowage rack to the rear of the hull. Attach the hull MG to the glacis plate.īelow: The hull MG attached to the front of the hull.īelow: With the hull MG in place, the hull of the M4 Sherman (Late 75mm) is fully assembled.īelow: With the turret added the hull our M4 Sherman (Late 75mm) is now complete.Ĭomponents Required For The M4 Sherman (Late 76mm) Attach the 75mm gun to the gun trunnion.īelow: With the 75mm gun in place, the M4 Sherman (Late 75mm) turret is now fully assembled. Attach the 75mm gun trunnion to the front of the turret.īelow: The back of the 75mm gun trunnion of the has an arrow to indicate which way is up.īelow: The 75mm trunnion attached to the front of the turret.īelow: The back of the 75mm gun also has an arrow to indicate which way is up. Attach the hatch to the inside of commander's cupola. Attach the stowage rack to the rear of the hull.īelow: With the stowage rack attached, the basic hull of the M4 Sherman is now fully assembled. Tip: When referring to left or right-hand side in regards to a Flames Of War miniature, the orientation is determined as if looking at the vehicle from the rear.īelow: The upper and lower hulls now joined. Next, attach the upper hull section to the lower hull. It gives the strongest bond when gluing plastic to plastic.īelow: The left-hand side track attached to the hull.īelow: The right-hand side track attached to the hull. Tip: Although regular Hobby Glue can be used to assemble plastic vehicles, we recommend that you use good quality plastic cement instead. Note: Each track has been keyed to correspond with a particular side of the hull this aids in ensuring the correct orientation of the tracks when assembling the miniature. ![]() Next, attach the tracks to the lower hull. Begin byattaching the final drive section to the front of the lower hull. How to assemble your M4 Sherman (Late) TankĬheck out the M4 Sherman (Late) Platoon spotlight here. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |